Teknika Kapal Niaga

  • analog training kit

    Analog Circuit Training Kit

    0 out of 5

    SPESIFIKASI

    • Input power : single-phase, three-wire AC220V±10% 50Hz/60Hz
    • Output power : DC±5V continuously adjustable, DC±12V , DC+5V -+27V
    • Continuous adjustable DC
    • power supply Capacity : < 200VA
    • Adjustable signal source : 2— 20KHZ , adjustable amplitude , three kinds of signal output , frequency coarse and fine tune
  • band saw

    Band Saw Machine

    0 out of 5

    Capacity:

    • Circular @90°: approx. 229 mm (9″)
    • Rectangular @90°: approx. 127×405 mm (5″x16″)
    • Circular @45°: approx. 150 mm (6″)
    • Rectangular @45°: approx. 150×190 mm (6″x7.5″)
    • Blade speed: @60 Hz: approx. 22-122 MPM 95-402 FPM
    • @50 Hz: approx. 18-102 MPM 78-335
    • FPM Blade size: approx. 27 x 0,9 x 32155 mm
    • Motor power: approx. 1,5 KW 2 HP (3 PH)
    • Drive: V-Belt
  • basic hydrolik

    Basic Electro Hydraulic Training System

    0 out of 5
    • Hydraulic power unit: Work power: AC:380V
    • Frequency:50Hz
    • Safety rate-limiting range:1000- 1500 r/min
    • Power: approx. 1.1KW
    • Flow: approx. 4.5L/min Oil box volume: approx. 35Ltr Gear pump system: motor pump using open shelf installation, structure compact, low noise, easy to maintenance
    • Part list: Training table, Hydraulic station, Double acting hydraulic cylinder, throttle valve, One-way throttle valve, Pressure relief valve (directly actuated), 4/3 Way solenoid valve (M) ,4/3 Way solenoid valve (O), 4/3 Way solenoid valve (Y), 4/3 Way solenoid valve (H), 4/2 Way solenoid valve, 4/2 Way manual shuttle valves, Speed regulator valve , Pilot Relief Valve, Pressure relief valve (pilot actuated), Pilot pressure reducing valve, Hydraulic control one-way valve, One-way valve, Pressure relay, T connector, Five way connector, hydraulic distributor, Glycerin pressure gauge, Hose 0.6m, Hose 1m, Hose 1.5m, DC power module, Relay module, Button switch module, power unit for hydraulic pump, Photoelectric sensor, Capacitive sensor, Inductive sensor, Micro switch module (left), Micro switch module (right), Test line, Toolkit, Hydraulic Simulation Software. User manual.
  • basic pneumatic

    Basic Electro Pneumatic Training System

    0 out of 5

    SPESIFIKASI :

    • DC power: Input, AC220V, 50Hz/60 Hz
    • Output: DC 24V/3A Air compressor: Power: AC 220V±10% 50Hz/60Hz Motor power: approx. 480W Nominal volume: approx. 6L normal Output approx. 0.8 MPa Noise degree: approx. 66 dB
    • Part list: Workbench, Silent Air compressor, Manifold block (air terminal), Double-acting cylinder, Single-acting cylinder, 5/3 solenoid directional valve central vented, 5/3 solenoid directional valve central exhaust, 5/3 solenoid directional valve central pressure, 5/2 single solenoid shuttle valve, 5/2 double solenoid shuttle valve, 3/2 single solenoid shuttle valve NC, 3/2 single solenoid shuttle valve NO, 5/2 handle shuttle valve Mushroom button valves (Mushroom button valves), 5/2 handle shuttle valve, 5/3 handle shuttle valve, Single pneumatic control 3/2, Double pneumatic control 3/2, Single pneumatic control 5/2, Double pneumatic control 5/2, Dyad(pressure regulator & air filter), Reducing valve, One-way valve, Pressure gauge, One-way throttle valve, 3/2 knob valve, 3/2 Stroke valve, 3/2 Stroke valve, 3/2 knob valve (3/2 push botton valve), Time delay valve, Sequence valve, “And” gate-type dual pressure Valve, “Or” gatetype shuttle valve, Quick escape valve, Micro switch valve (left trigger), Micro switch valve (Right trigger), Photoelectric Sensor,capacitive sensor, Conductive sensor, Test wire, DC power supply unit, Relay, Button switch unit, Hose Ф4, Hose Ф6, 4 T Valve, T connection, APG reducing straight coupling, Tool kits, Pneumatic Simulation software, User manual.
  • basic electronik trainer

    Basic Electronics Trainer

    0 out of 5
    • Input power: Single phase three wire AC220V±10% 50Hz;
    • Output parameters: 2 way DC +1.25~+30V/0.8A; DC±5V/1A, DC±12V/1A; 2 way AC 7.5V, 2 way AC 15V; Compatible with independent winding and neutral axle output
    • Protection measures: AC 220V, safety socket & safety terminal output Capacity:<1KVA Configuration list: Training platform AC220V main control power box AC220V power box Voltage stabilized power supply module I Adjustable DC voltage stabilized power supply module AC power supply Signal generator module Measuring instrument module Mask plate hanging line experiment module Analog circuit experiment box 14P Digital chip module 16P Digital chip module 18P Digital chip module 20P Digital chip module Comprehensive test box module Test line and power line Terminal test line(K2 and K3), Power line Manual book CD Electronic chip
  • Digital Circuit Training Kit

    Digital Circuit Training Kit

    0 out of 5
    • SPESIFIKASI :
      • Input power: single-phase, three-wire AC 220V±10% , 50Hz/60Hz
      • Output power : DC±5V continuously adjustable, DC±12V, DC+5V─+27V Continuous adjustable DC power supply Capacity : < 200VA One set adjustable signal source : 2—20KHZ, adjustable amplitude. Three kinds of signal output ,the frequency coarse and fine tune
      • Part list: Digital experiment box, Power area, Logic pen, einmal pulse source, signal generator, frequency meter unit, Resistance part, capacitance part, audion part, Integrated circuit, Logic level show, logic level output unit, Bread board area unit, Date capture card, Power line, Testing line, Manual book
  • Digital optical measurement profile projector

    Digital optical measurement profile projector

    0 out of 5
    • Projection screen rotation range: 0-360° X-axis travel (mm) 0~200 Min. travel 0.001mm Y-axis travel (mm) 0~80 (focusing) Z-axis travel (mm) 0~150 Min. travel 0.001mm X,Y coordinate indicating value
    • accuracy: v(3+L/75) μm, (L is Measured length, unit is mm)
  • Drill Press

    Drill Press

    0 out of 5
    • Voltage/Frequency:230V-/50Hz
    • Input power: approx. 350W
    • Max drilling capacity: Ø approx. 13mm
    • Spindle Travel: approx. 50mm
    • Column Diameter: approx. 46mm
    • Spindle speed:5speed: approx. 760~3070rpm
    • Distance Spindle/Column approx. 104mm
    • Distance Spindle/Table approx. 200mm
    • Distance Spindle/Base approx. 290mm
    • Table size: approx. 160x160mm
    • Base size: approx. 291x183mm
  • Electric Drill

    Electric Drill

    0 out of 5
    • Voltage/Frequency:230V/50HZ
    • Input power: approx. 300W
    • 10MM keyless chuck No load speed: 0-400/0- 1400rpm
    • Torque set: 23+1
    • Max torque force: approx. 35N.m
  • Engine Room Simulator

    Engine Room Simulator

    0 out of 5
    • Configured with realistic consoles and several large monitor so to reproduce the ER different areas.
    • Engine
      • Low Speed diesel, with CPP or FPP, with conventional or electronic control
      • Medium Speed diesel,
      • Medium Speed diesel, up to 4 engines, gear and CPP
      • Steam turbine, with FPP
      • Gas turbine, with CPP
      • All related auxiliary equipment (electricity generation, Sea water cooling, Lubricating oil etc as below specified) – AuxiliAry system
      • Air Conditioning and refrigeration Plant
      • Power Plant
      • Treatment Plant (separators, reverse osmosis system, etc.)
      • Freshwater plant
      • Marine equipment (Compressors, pumps,Monitoring Systems, Heat Exchangers, etc.)
  • Gerinda Listrik Tangan

    Gerinda Listrik Tangan

    0 out of 5
    • Voltage: 230V/50HZ
    • Power: approx. 650W
    • No-Load speed: approx. 11000rpm
    • Diameter: Φ approx. 100mm
    • Thread of Grinder spindle:M10
  • Hand Tool Set

    Hand Tool Set

    0 out of 5
    • Combination pliers 6″, Long nose pliers 6″, Bent nose pliers 6″, Flat nose pliers 6″, Diagonal cutting pliers 6″, End cutting pliers 6″, 8pcs Handtools set, Pump pliers 10″, Rabbit pliers 8″, Pipe wrench 18″, Bolt cutter 18″, 4pcs Circlip plier set 7″, Round head quick grip clamp pliers 10″, Long nose quick grip clamp pliers 9″, Antiviation tin slip 10″, Antiviation tin slip(left) 10″, Tin slip 10″, Hedge shear 52CM, Lopper 70CM, Wire stripper 7″, Duck mouth stripping pliers 7″, PVC pipe cutter 42mm, Slim taper files 8″, Triangle steel file 8″, Flat steel file 8″, Half round steel file 8″, Round steel file 8″, 5pcs Steel file set 8″, Machinist hammer 500g, Rubber hammer 16oz, Screwdriver sets, Slotted screwdriver 6×150mm, Screwdriver 6×150mm, Pozidriv screwdriver 6×150mm, Insulated screwdriver 4×100mm, Insulated screwdriver PH2×100mm, Insulated screwdriver PZ2×100mm, 6pcs precision screwdriver, 9pcs Ball point hex key, 9pcs Torx hex key, 8pcs Double open end spanner set, 8pcs Combination spanner set, 8pcs Offset ring spanner set, Adjustablewrench 12″, Y-Type socket wrench 8*10*12, Y-Type socket wrench 12*14*17, T-handle socket wrench 8*200*300, T-handle socket wrench 10*200*300, T-handle socket wrench 12*200*300, Thandle socket wrench 13*200*300, T-handle socket wrench 14*200*300, 19pcs 1/2″ socket set, Hacksaw frame 12″ 510g, Self-loading Zinc-Alloy cutter with 6pcs blades, Vernier caliper, Steel measuring tape 5m, Hand riveter 10″, Screwdriver tester 190mm
error: Maaf, Konten sudah di proteksi !