Teknik Elektronika

  • Advance Electro Hydraulic Training System

    Advance Electro Hydraulic Training System

    0 out of 5

    SPESIFIKASI :

    Hydraulic power unit:

    • Work power: AC:380V
    • Frequency:50Hz
    • Safety rate-limiting range:1000-1500 r/min
    • Power:1.1KW
    • Flow:4.5L/min
    • Oil box volume: 35Ltr
    • Gear pump system: motor pump using open shelf installation, structure compact, low noise, easy to maintenance

    Part list:

    • Training workbench, Hydraulic station, Double-acting hydraulic cylinder, One-way throttlevalve,Throttle valve, Pressurerelief valve (directly actuated), 4/3 Way solenoid valve (M), 4/3-WAY solenoid valve(O), 4/3 Way solenoid valves( Y), 4/3-WAY solenoid valve ( H) ,4/2 Way solenoid valve, 4/2 Way manual shuttle valves, Speed regulator valve, Pilot relief valve,Piloted sequence valve, Pilot type pressure reducing valve, Piloted operated check valve, Check valve, Pressure relay, T connector, Five way connector,Hydraulic distributor, Glycerin pressure gauge, Hose 0.6m,Hose 1m, Hose 1.5m, DC powermodule, Relay module, Buttonswitch module, Power supply forhydraulic pump use,Photoelectric sensor, Capacitysensor, Inductive sensor, Microswitch module (left), Micro
      switch module (right), PLCmodule(Siemens), PLCprogramming software(Siemens), Download cable(Siemens), Testline, Toolkit ,Manual.
  • am transceiver kit

    AM Transceiver Trainer Module

    0 out of 5

    SPESIFIKASI :

    • Receiver Section
      • Sensitivity : About 2μV
      • Intermediate Frequency : approx. 455kHz
      • Frequency Control : Variable and X-Tal
    • Transmitter Section
      • RF Output : 5W Max.
      • P.A Tank Circuit : Ï€- Network
      • Oscillation Mode : X-Tal and LC Circuit(Variable Control)
    • General Characteristics
      • Frequency Range : 3.5MHz~12MHz(2-Band)
      • Electro-Wave Mode : approx. AM/CW
      • Antenna Impedance : approx. 50/75Ω
      • Input Voltage : AC 220V, 50/60Hz
  • analog training kit

    Analog Circuit Training Kit

    0 out of 5

    SPESIFIKASI

    • Input power : single-phase, three-wire AC220V±10% 50Hz/60Hz
    • Output power : DC±5V continuously adjustable, DC±12V , DC+5V -+27V
    • Continuous adjustable DC
    • power supply Capacity : < 200VA
    • Adjustable signal source : 2— 20KHZ , adjustable amplitude , three kinds of signal output , frequency coarse and fine tune
  • antenna training kit

    Antenna Trainer Kit

    0 out of 5

    SPESIFIKASI :

    • Overview : 16 different types of Antenna
    • RF source generation : 500MHz, 2GHz and 10GHz Software simulation of radiation Patterns and characteristics of Antenna Antenna Directional Coupler (Manual / Remote)
    • Experiments : Practice of assembling and installing various types of Antenna, Practical experiments of vertical/horizontal directional characteristics, Antenna’s efficiency and gain calculation and measurement, and Interference experiments
    • RF Generator :
      • Frequency Range : 500MHz, 2GHz, 10GHz,
      • Power Range : 10mW(Approx.),
      • Output Impedance : 50Ω(Nominal),
      • Modulation Frequency : 1kHz.
    • Receiver & Control :
      • RF Input Level : -50.0dBm~-10.0dBm,
      • Ant. Directional Control Range : 0Ëš~ 360Ëš,
      • Ant. Rotor Angle Control : 1Ëš/step, 5Ëš/step, 10Ëš/step, Manual / PC Interface(RS-232C).
  • Hot
    Audio System Trainer

    Audio System Trainer

    0 out of 5

    Deskripsi

    • Trainer dapat digunakan pada percobaan di ruang laboratorium atau sebagai alat pengajaran dan praktek mengenai sistem suara mono maupun stereo
    • Trainer ini dirancang untuk kemudahan analisa dan aplikasi teknik pengukuran suara/audio
    • Sistem trainer menggunakan blok modular untuk memudahkan siswa belajar PLC secara modular.
    • Konstruksi tipe panel memudahkan siswa saat melakukan percobaan.
    • Semua masukan dan keluaran pada masing-masing panel dilengkapi dengan soket 4mm untuk memudahkan dalam penyambungan
    • Setiap panel dilengkapi rangkaian pengaman kelebihan tegangan dan arus
    • Lengkap dengan buku petunjuk percobaan
      untuk menuntun siswa langkah demi langkah dalam melakukan percobaan.

    Spesifikasi

    • Power Supply [ PTE-032-01 ]
      – Tegangan masukan : AC 220V / 50Hz
      – Tegangan keluaran : DC +15V dan -15V
      – Arus keluaran : 2A
    • Input Selector [ PTE-032-02 ]
      -Sumber masukan : Tape, Tuner & CD dan Aux.
      – Jenis terminal masukan : RCA Jack stereo
    • Stereo Pre Amplifier [ PTE-032-03 ]
      – Modul pra penguat universal untuk macam-macam surmber sinyal
      – Dilengkapi dengan : rangkaian penguat Mikropon
      – Mode operasi : Mono & Stereo
      – Tegangan masukan : +15VDC
      – Respon frekuensi : 20Hz – 50kHz
    • Stereo Tone Control [ PTE-032-04 ]
      – Fungsi kontrol : Volume, Bass, Treble and Balance
      – Mode operasi : Mono & Stereo
      – Tegangan masukan : +15VDC
      – Impedansi masukan : 120kW
      – Respon frekuensi : 20Hz – 90kHz
    • Stereo Power Amplifier [ PTE-032-05 ]
      – Tipe daya : OCL
      – Daya keluaran : 20W / 4W
      – Mode operasi : Mono & Stereo
      – Tegangan masukan : +15VDC and -15VDC
      – Impedansi masukan : 40kW
      – Impedansi beban : 4W / 8W
    • Loudspeaker [ PTE-032-06 ]
      – Impedansi masukan : 8W / 20W
      – Saklar mode : Internal & External speaker
    • Dummy Load [ PTE-032-07 ]
      – Impedansi masukan : 8W / 25W (2 channel)
  • basic pneumatic

    Basic Electro Pneumatic Training System

    0 out of 5

    SPESIFIKASI :

    • DC power: Input, AC220V, 50Hz/60 Hz
    • Output: DC 24V/3A Air compressor: Power: AC 220V±10% 50Hz/60Hz Motor power: approx. 480W Nominal volume: approx. 6L normal Output approx. 0.8 MPa Noise degree: approx. 66 dB
    • Part list: Workbench, Silent Air compressor, Manifold block (air terminal), Double-acting cylinder, Single-acting cylinder, 5/3 solenoid directional valve central vented, 5/3 solenoid directional valve central exhaust, 5/3 solenoid directional valve central pressure, 5/2 single solenoid shuttle valve, 5/2 double solenoid shuttle valve, 3/2 single solenoid shuttle valve NC, 3/2 single solenoid shuttle valve NO, 5/2 handle shuttle valve Mushroom button valves (Mushroom button valves), 5/2 handle shuttle valve, 5/3 handle shuttle valve, Single pneumatic control 3/2, Double pneumatic control 3/2, Single pneumatic control 5/2, Double pneumatic control 5/2, Dyad(pressure regulator & air filter), Reducing valve, One-way valve, Pressure gauge, One-way throttle valve, 3/2 knob valve, 3/2 Stroke valve, 3/2 Stroke valve, 3/2 knob valve (3/2 push botton valve), Time delay valve, Sequence valve, “And” gate-type dual pressure Valve, “Or” gatetype shuttle valve, Quick escape valve, Micro switch valve (left trigger), Micro switch valve (Right trigger), Photoelectric Sensor,capacitive sensor, Conductive sensor, Test wire, DC power supply unit, Relay, Button switch unit, Hose Ф4, Hose Ф6, 4 T Valve, T connection, APG reducing straight coupling, Tool kits, Pneumatic Simulation software, User manual.
  • Hot
    Basic Electronic Trainer

    Basic Electronic Trainer

    0 out of 5

    Deskripsi

    • Trainer ini berbentuk modular dan dilengkapi dengan sistem pengajaran untuk memudahkan siswa mempelajari tentang dasar elektronika.
    • Trainer ini dapat mempresentasikan dan melatih prinsip-prinsip dasar elektronika mencakup komponen elektronika, pengaturan, stabililisasi dan proteksi dari catu daya; aplikasi komponen dalam rangkaian,penguat operasional (op-amp) dan rangkaian penapis.
    • Trainer ini dilengkapi dengan papan rangkaian, yang dapat digunakan untuk berlatih membuat rangkaian menggunakan komponen diskrit yang tersedia seperti resistor, kapasitor, transistor dan lain lain. Juga dilengkapi dengan jembatan penghubung dan kabel penyambung yang dapat dihubungkan dengan catu daya.
    • Trainer ini berbentuk panel, mudah di operasikan.

    Spesifikasi

    • Assembly Board untuk TPS Panel
      – Mountable frame standar digunakan untuk perakitan sirkuit dari komponen modular
      – 24 socket grids dengan 24 conducting squares dan 216 sockets
      – 6 socket grids dengan 36 sockets
      – 2 conducting path with 18 sockets each
      – ukuran : 297 x 300 mm
    • Power Supply
      – Tegangan output : DC 5V / 1A, 15V / 2A, -15V / 2A
      – Tegangan input : AC 220V, 1 phase 50Hz
      – Koneksi output : 4mm sockets
      – Ukuran  : 114 x 297 mm
    • Tegangan/Current Source
      – Sumber tegangan  : DC Variabel 0 up to 12V / 250mA
      – Current source : 0 up to 500mA
      – Tegangan input : 220V, 1 phase 50Hz
      – Tegangan output : 4mm sockets
      – Ukuran  : 114 x 297 mm
    • Basic Meter
      – Amperemeter, range : 100uA -100mA -1A and 5A (DC)
      – Voltmeter, range : 100mV -1V -10V and 50V (DC)
    • Section Boxes, terdiri dari :
      – Diode 1A, Diode Zener, DIAC, LED
      – Resistors, Potensiometers
      – Transistors, TRIAC, SCR, FET
      – LDR, NTC, PTC
      – Relay Model
      – Op-Amp
      – Switch Change-Over SPDT
      – Kapasitors and VARCO
      – UI Core with 500 and 1000 Winding Coil
  • basic electronik trainer

    Basic Electronics Trainer

    0 out of 5
    • Input power: Single phase three wire AC220V±10% 50Hz;
    • Output parameters: 2 way DC +1.25~+30V/0.8A; DC±5V/1A, DC±12V/1A; 2 way AC 7.5V, 2 way AC 15V; Compatible with independent winding and neutral axle output
    • Protection measures: AC 220V, safety socket & safety terminal output Capacity:<1KVA Configuration list: Training platform AC220V main control power box AC220V power box Voltage stabilized power supply module I Adjustable DC voltage stabilized power supply module AC power supply Signal generator module Measuring instrument module Mask plate hanging line experiment module Analog circuit experiment box 14P Digital chip module 16P Digital chip module 18P Digital chip module 20P Digital chip module Comprehensive test box module Test line and power line Terminal test line(K2 and K3), Power line Manual book CD Electronic chip
  • Bor Meja

    Bor Meja

    0 out of 5

    Spesifikasi :

    • Max. Driling Capacity : 25 mm
    • Diameter of Column : 102 mm
    • Spindle travel : 130 mm
    • Distance spindle axis to column surface : 230 mm
    • Max. distance spindle nose to worktable : 750 mm
    • Max. distance spindle nose to base : 990 mm
    • Spindle taper : MT.3
  • cctv trainer kit

    CCTV Security System Training Kit

    0 out of 5

    SPESIFIKASI :

    • 12VDC Power Supply Digital Video Recorder Control 4 Channel video recorder
    • Digital Video Recorder AV Transmitter Code approx. 0.1W Mini A/V 8 Channel AV Receiver AV RECEIVER approx. 100mA Camera Lens approx. 2.8mm F1.4 Auto Iris Lens (DC) 4mm manual Iris
    • Pin Hole Camera approx. 1/3” CCD 420TV Line, approx. 0.2 Lux, Lens : approx. 3.6mm
    • PIR Hidden Camera 420TVL/ approx. 0.5 Lux/F2.0 12VDC/With LED/ approx. 3.6mm Lens Audio Function IR Camera Code approx. 1/4” Sharp Color CCD 420 TVL Lens : approx. 6mm IR Camera With Metal Casing IR Camera 12VDC
    • Dome Camera Code approx. 1/3” Sharp Color CCD Sensor 380TVL 1 Lux/F2.0 12VDC / approx. 3.6mm Lens 8 Channel A/V Transmitter Unique frequencies provide
    • 8 channel Audio/Video Wireless transmission distance approx. 1500m available(Line of Sight) Support connection with Yagi Antenna or SMA Antenna replaceable
    •  CCD Camera Code approx. 1/3” Color CCD 380 TV Line Built in Microphone, approx. 0.5 Lux jpeg Smoke Detector Camera approx. 1/3” Sharp Color CCD Sensor Smoke Detector Camera 380TVL 1 Lux/F2.0 12VDC/ approx. 3.6mm Lens
    • Monitor Safety Connecting Lead approx. 4mm connecting Lead Vertical Frame High Level : Din Standard approx. A4 with two shelfs Material : Aluminium Side Frame :T shape
  • Hot
    Circuit Aplication Trainer

    Circuit Aplication Trainer

    0 out of 5

    Deskripsi

    • Dirancang untuk mempresentasikan dan praktek aplikasi elektronika dasar yang meliputi: regulasi, stabilisasi dan proteksi catu day, serta penerapan komponen pada rangkaian dan rangkaian penguat operasional
    • Sistem blok modular memudahkan siswa belajar aplikasi elektronik dasar secara modular. Konstruksi tipe panel memudahkan siswa saat melakukan percobaan.
    • Semua masukan dan keluaran masing-masing panel dilengkapi dengan soket 4mm untuk memudahkan penyambungan
    • Jembatan penghubungm kabel penghubung dan peralatan penyambung lainnya diberikan dalam jumlah yang cukup untuk melakukan seluruh percobaan
    • Lengkap dengan buku petunjuk percobaan untuk menuntun siswa langkah demi langkah dalam melakukan percobaan.

    Spesifikasi

    • Assembly Board for TPS Panel [ GSE 110 ]
      – Dapat dipasang pada frame standar, digunakan untuk merangkai rangkaian percobaan dari komponen modular
      – 24 soket grid, masing-masing soket grid terdiri dari 9 soket yang saling berhubungan 4 jalur konduktif horisontal, masing-masing jalur memiliki 18 soket yang saling terhubung
      – Dimensi: 297 × 300 mm
    • Power Supply [ PTE-015-01 ]
      – Tegangan keluaran : DC 5V / 1A ; 15V / 2A ; -15V / 2A
      – Tegangan masukan : AC 220V, 1 fasa 50Hz
      – koneksi keluaran : soket 4mm
      – Dimensi : 114 × 297 mm
    • Staircase Generator [ PTE-015-02 ]
      – Tegangan masukan : +15 VDC, -15 VDC
      – koneksi keluaran : soket 4mm
      – Dimensi : 114 × 297 mm
    • Basic Meter [ KAL-41 ]
      – Amperemeter : 100µA – 100mA – 1A and 5A ( DC)
      – Voltmeter : 100mV – 1V – 10V and 50V (DC)
    • Section Boxes, terdiri dari:
      – Dioda jembatan 1A, Dioda 1A, Dioda zener, DIAC, LED
      – Regulator
      – Resistor, Potensiometer
      – Transistor
      – Op-Amp
      – Saklar SPDT
      – Buzzer
      – Relai
  • Circuit Board Engraving Machine

    Circuit Board Engraving Machine

    0 out of 5

    SPESIFIKASI :

    • Technical Parameter The finest processing conductor width/spacing: approx. 0.1mm(4mil)
    • Processing hole diameter : 0.2mm (8mil)
    • Processing format : approx. 305mm x 230mm
    • Using Germany high-speed electric spindle with speed : approx. 60000rpm
    • Repeat positioning accuracy : ≤±5μm
    • System positioning accuracy : ≤±20μm
    • Contour through the milling speed : approx. 6mm/s
error: Maaf, Konten sudah di proteksi !